Everyone wants a good speed broadband connection. So, either you get one or u make a low speed broadband into a high speed broadband.
These settings will allow you to increase the speed of your Broadband Internet Connection
when using a Cable Modem or DSL Router with Windows 2000 and Windows XP.
Open your registry and find the current configuration key below....
Create the following DWORD values, as most of these values will not already exist you will need to create them by clicking on 'Edit -> New -> DWORD Value' and then set the value as shown below.
DefaultTTL = "80" hex (or 128 decimal)
This specifies the default time to live (TTL) for TCP/IP packets. The default is 32.
EnablePMTUBHDetect = "0"
This specifies whether the stack will attempt to detect Maximum Transmission Unit (MTU) routers that do not send back ICMP fragmentation-needed messages. The default is 0.
EnablePMTUDiscovery = "1"
This specifies whether the TCP/IP stack will attempt to perform path MTU discovery as specified in RFC 1191. The default is 1.
GlobalMaxTcpWindowSize = "7FFF" hex (or 32767 decimal)
This specifies the system maximum receive window size advertised by the TCP/IP stack.
TcpMaxDupAcks = "2"
This determines the number of duplicate ACKs that must be received for the same sequence number of sent data before "fast retransmit" is triggered.
SackOpts = "1"
This enables support for selective acknowledgements as documented by Request for Comment (RFC) 2018. Default is 0.
Tcp1323Opts = "1"
This controls RFC 1323 time stamps and window scaling options. Possible values are: "0" = disable RFC 1323 options, "1" = window scale enabled only, "2" = time stamps enabled only and "3" = both options enabled.
TcpWindowSize = "7FFF" hex (or 32767 decimal)
This specifies the receive window size advertised by the TCP/IP stack. If you have a latent network you can try increasing the value to 93440, 186880, or 372300.
Now, exit your registry and restart Windows for the changes to take effect.
If you don’t want to edit the registry, here's the TCP utility that is ideal for you...
These settings will allow you to increase the speed of your Broadband Internet Connection
when using a Cable Modem or DSL Router with Windows 2000 and Windows XP.
Open your registry and find the current configuration key below....
Create the following DWORD values, as most of these values will not already exist you will need to create them by clicking on 'Edit -> New -> DWORD Value' and then set the value as shown below.
DefaultTTL = "80" hex (or 128 decimal)
This specifies the default time to live (TTL) for TCP/IP packets. The default is 32.
EnablePMTUBHDetect = "0"
This specifies whether the stack will attempt to detect Maximum Transmission Unit (MTU) routers that do not send back ICMP fragmentation-needed messages. The default is 0.
EnablePMTUDiscovery = "1"
This specifies whether the TCP/IP stack will attempt to perform path MTU discovery as specified in RFC 1191. The default is 1.
GlobalMaxTcpWindowSize = "7FFF" hex (or 32767 decimal)
This specifies the system maximum receive window size advertised by the TCP/IP stack.
TcpMaxDupAcks = "2"
This determines the number of duplicate ACKs that must be received for the same sequence number of sent data before "fast retransmit" is triggered.
SackOpts = "1"
This enables support for selective acknowledgements as documented by Request for Comment (RFC) 2018. Default is 0.
Tcp1323Opts = "1"
This controls RFC 1323 time stamps and window scaling options. Possible values are: "0" = disable RFC 1323 options, "1" = window scale enabled only, "2" = time stamps enabled only and "3" = both options enabled.
TcpWindowSize = "7FFF" hex (or 32767 decimal)
This specifies the receive window size advertised by the TCP/IP stack. If you have a latent network you can try increasing the value to 93440, 186880, or 372300.
Now, exit your registry and restart Windows for the changes to take effect.
If you don’t want to edit the registry, here's the TCP utility that is ideal for you...
.png "English"){kind=small}
0 comments:
Post a Comment